> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/morpho-biometric-integration/troubleshooting-morpho-biometrics.md).

# Troubleshooting - Morpho Biometrics

The following table describes some of the known issues that can occur with the installation of Morpho Readers, and possible solutions:

<table><thead><tr><th width="222">Problem</th><th width="312">Possible Cause(s)</th><th>Solution</th></tr></thead><tbody><tr><td>Reader not coming online</td><td>Network wiring incorrect</td><td><p>Either:</p><ul><li>refer to <a href="https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/morpho-biometric-integration/installing-morphoaccess-readers/ma-sigma-morphowave-visionpass-sp-and-visionpass-wiring.md">MA Sigma, MorphoWave and VisionPass Wiring</a> for wiring instructions, or</li><li>refer to <a href="https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/morpho-biometric-integration/installing-morphoaccess-readers/configuring-a-biometric-reader/configuring-morpho-readers-using-mbta-application.md">Configuring Morpho Sigma and MorphoWave Readers using MBTA application</a> Steps 6-11 for instructions on how to unlock the On-demand Security state.</li></ul></td></tr><tr><td></td><td>No Morpho readers in Command Centre license file</td><td><p>Obtain a new Command Centre license file that includes the Morpho feature.</p><p>Contact Cardax Technical Support.</p></td></tr><tr><td>Enrolment reader locks up</td><td>No dongle</td><td>Obtain a dongle. Uninstall the Sentinel software, and then reinstall it.</td></tr><tr><td>Reader generates <em>"Input parameters are not valid"</em> errors in the Trace Log file</td><td>Insufficient power to the reader</td><td><p>Either:</p><ul><li>connect readers directly to local power supplies (and not to Gallagher Controllers or URIs), or</li><li>use thicker power supply wire (allows greater distance between power supply and reader)</li></ul></td></tr><tr><td><p>Reader appears to be working, but:</p><ul><li>‘Access Denied’ tone sounds,</li><li>the door opens, and</li><li>an <em>‘Access Granted’</em> event is generated</li></ul></td><td>Incorrect wiring</td><td>Refer to <a href="https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/morpho-biometric-integration/installing-morphoaccess-readers/ma-sigma-morphowave-visionpass-sp-and-visionpass-wiring.md">MA Sigma, MorphoWave and VisionPass Wiring</a> for wiring instructions.</td></tr><tr><td rowspan="2">Reader generates <em>“Re-sync Access Failed</em>” or <em>“Updating the configuration failed”</em> alarm, and shows “The reader has rejected some configuration and a firmware update may be required to ensure correct terminal behaviour” in the status</td><td>Wrong firmware on reader</td><td>Upgrade reader firmware. Refer to <a href="https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/morpho-biometric-integration/installing-morphoaccess-readers/upgrading-the-morphoaccess-reader-firmware.md">Upgrading the MorphoAccess Reader Firmware</a>.</td></tr><tr><td>MIFARE Classic and DESFire keys are not initiated</td><td>Initialise the keys under <strong>Morpho Biometric Type</strong> > <strong>Card Encoding</strong>.</td></tr><tr><td>You get the error message <em>"The selected permitted card technology settings are not supported by the biometric reader"</em> when setting permitted card technologies on the Card Reader properties.</td><td>If you attempt to set a morpho reader to follow the site default, but the site default does not allow either of the card technologies that the morpho reader does (MIFARE Classic or DESFire).</td><td><p>Either:</p><ul><li>change the server settings to allow at least one of those two card technologies, or</li><li>have the Morpho reader NOT follow the site-wide settings.</li></ul></td></tr><tr><td>T20 reader unresponsive when trying to put in the PIN when 'Secure + PIN' mode with VisionPass next to T20 reader.</td><td><p>VisionPass reader does not support 'Secure + PIN'</p><p>mode and is attempting to grant access through VisionPass reader.</p></td><td>Add VisionPass reader to the same Controller as the T20 reader.</td></tr><tr><td>OSDP Morpho reader not coming online with status displaying "The device is not responding".</td><td>The reader has been replaced.</td><td>Perform a "Push Configuration" override.</td></tr><tr><td>OSDP Reader not coming online.</td><td>network disconnection,<br>device offline.</td><td>Remove OSDP reader from the OSDP tab of the Controller and then add it back again.</td></tr><tr><td>Bad packet alarm generated Invalid packet type: 0x6B</td><td>Using a MorphoWave SP reader with old firmware can cause this scenario when "Show reader display messages" is ticked.</td><td><p>Either:</p><ul><li>turn off "Show reader display messages" as the MorphoWave SP does not have an LCD screen, or</li><li>update the firmware to the latest version.</li></ul></td></tr><tr><td>Slow read rate when using cards with MorphoWave SP.</td><td>OSDP Display Messages Turned on.</td><td>Turn off OSDP Reader Display Messages.</td></tr><tr><td><p>VisionPass access reader does not load face templates.</p><p>VisionPass denies access when badging a VisionPass DESFire card + bio.</p></td><td>Enrolled with VisionPass SP</td><td>Enrol with VisionPass reader.</td></tr><tr><td>QR code authentication does not work</td><td>VP or VPSP reader firmware update</td><td>Please call GGL Tech Support to get patch file for this issue.</td></tr></tbody></table>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/morpho-biometric-integration/troubleshooting-morpho-biometrics.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
