The IP Alarm Transmitter requires no additional hardware; only the Controller is required.
Firmware requirement: To use IP Alarms, the Controller must be using Application version 2-3-11 or higher. Check the 'Application' field in the Controller's properties.
If the customer requires third-party monitoring, you can configure the IP Alarm Transmitter as an alternative or addition to the Permaconn or Alula alarm transmitter.
In the SMB Installer Portal, click the MONITORING tab.
Enter the Account Code received from the monitoring station and click SAVE.
The IP Alarm Transmitter item displays.
Enable the toggle next to the IP Alarm Transmitter.
Note: If you are also enabling the Permaconn or Alula alarm transmitter, select which transmitter is the primary one from the Primary option (next to the 'Account Code' field).
Click on the IP Alarm Transmitter to open its properties.
The IP Alarm Transmitter lightbox displays.
Select the required Protocol for transmitting to the monitoring station.
CSV uses Comma Separated Values (CSV) format for transmitting alarms. This method uses TCP/IP and is unencrypted.
DC-09 Gallagher uses Gallagher's own format of DC-09. Select this option if you are transmitting alarms to a Gallagher receiver. Encryption is available.
DC-09 SIA uses the Security Industry Association (SIA) protocol for DC-09. You will most likely want this option when transmitting to a third-party monitoring station. Encryption is available.
If you selected a DC-09 protocol, the Encryption check box displays. Optionally select this check box to encrypt all transmissions from the Controller, then enter the Encryption Key.
You can either generate this Encryption Key yourself and then provide it to the monitoring station, or request an Encryption Key from the monitoring station. Either way, the monitoring station must have the same key that you enter here.
For the IP Alarm Transmitter to provide authentication, select the Authentication check box and enter the Username and Password that will be used by the monitoring station to authenticate the data received.s
Note: The Username and Password must not contain the following characters: < > & ‘ “ ,
Enable as many Receivers as you like; there are two available. You must enable at least one Receiver for the IP Alarm Transmitter to function.
Transmissions are sent to 'Receiver 2' if attempts with 'Receiver 1' fail.
In the IP field of the enabled receiver(s), enter the IP address of the receiver. This must be provided to you by the monitoring station.
In the Port field of the enabled receiver(s), enter the Port used by the receiver. This must also be provided to you by the monitoring station.
To enable polling, select the time under the Polling field and enter how often a heartbeat will be sent to poll the receiver. Otherwise, select 'None'.
Click OK to complete the configuration.
A timer test or 'poll' (also known as the ‘periodic test’ or ‘24 hour’ test) is an affirmation to the monitoring station that the alarm system is capable of sending Contact ID. Most alarm systems send one test per day. The signal is fixed in its format and will be sent with an XYZ (Contact ID event code) of 602 and it will be sent in the (GG) partition or Alarm Zone 00. Only one periodic test can be enabled per account number for accurate reporting of line status (this is a consideration when using multiple Diallers using single client code reporting). It may be necessary to configure periodic tests from different diallers into different account numbers. It will also be reported as a new event and will have a CCC of 000, (e.g. 123418160200000, where 1234 is the account number).
If a test ('poll') is not received when it should have been, action is taken by the monitoring station staff.
Publishing configuration with monitoring enabled pushes the monitoring-related configuration to the controller. This publishing is also the trigger for the controller to carry out dial checks and construct and send messages to the monitoring station.
THE MONITORING STATION WILL RECEIVE ALARMS FROM THE SITE WHENEVER MONITORING IS ENABLED AND A PERMACONN IS CONNECTED OR THE IP ALARM TRANSMITTER IS ENABLED (even if installation and configuration are still underway).
Monitoring Report
Generating the report Once a site is activated, a Monitoring Report will be available to download and send to the monitoring station. The Monitoring Report outlines the XZY Codes, GG Codes, Zone list CCC Codes, and User CCC Codes.
Under Site Actions on the right-hand side of the screen, click Download Monitoring Report.
A warning appears: Only published changes will appear in the report. NOTE: This report contains personal data. Please respect privacy laws.
Click Download.
The Monitoring Report downloads as a CSV file.
Send the file to the monitoring station.
As no users are created for the site yet, the User List CCC Codes will only contain the Key Account Holder. The Monitoring Report can be downloaded at any stage, and you may wish to wait until the Site is set up with more users before downloading and sending the report.
Users' CCC codes If an incident occurs and the monitoring station doesn’t know who the user is by name, they will have a CCC code. In the SMB app, the customer can search for this code.
For the Site Manager to find which user the CCC code is related to:
Log into the SMB customer app.
Select Team from the navigation bar.
In the search field, enter the CCC code.
The user with the related CCC code appears in the search results.