> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/site-monitoring/status-and-overrides/configuring-local-overrides-at-card-readers.md).

# Configuring Local Overrides at Card Readers

### Introduction

A local override at a reader enables Cardholders to arm or disarm the Alarm Zone associated with the Access Zone of a reader. A local override can also be used to change the [*access mode*](https://help.security.gallagher.com/knowledge-hub/configuration-client/glossary-of-terms.md#access-mode), (e.g. from Secure to Free) for the Access Zone associated with the reader.

**Note:** Cardholders require the appropriate privileges in order to perform local overrides at readers. Refer to the procedures below for details on how to configure the appropriate privileges for local overrides at readers.

There are three methods of performing local overrides, as follows:

1. For a Gallagher T20 Terminal connected as an HBUS Terminal, press the **Arm** button and then log on to the terminal. The required log on credentials are configured on the "Welcome Screen" tab of the HBUS Terminal item.

   For a Gallagher T20 Terminal connected as a Cardax IV Reader, press the **Arm** button and then perform the necessary action(s) in order to access the zone, (e.g. present your card) at the terminal.
2. For a Gallagher T20 Terminal connected as an HBUS Terminal, press the **Mode** button and then log on to the terminal. The required log on credentials are configured on the "Welcome Screen" tab of the HBUS Terminal item. The Access Mode screen displays on the terminal. Select the Access Mode you require.

   For a Gallagher T20 Terminal connected as a Cardax IV Reader, press the **Mode** button and then perform the necessary action(s) in order to access the zone, (e.g. present your card) at the terminal. Press the number, (i.e. 1, 2 or 3) representing the Access Mode you require, (i.e. Mode 1, Mode 2 or Scheduled).

   **Note:** You cannot perform an Access Zone override at a reader unless the Alarm Zone associated with the Access Zone is disarmed.
3. Badge your card twice, (known as a 'double-card override'), from any reader. Depending on what has been configured in Command Centre, this either overrides the mode of an Access Zone, alternating between Mode 2 and scheduled, or it arms the Alarm Zone associated with the reader.

   The following diagram describes how a double-card override is configured to arm the Alarm Zone associated with a reader.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-5e89a6a6a5929275dc14480f44b073bc2268a633%2Fcardoverridesdiagram_html.png?alt=media)

### Readers in elevators

If a reader has been installed in an elevator and a Cardholder performs an override at the reader, the override is attempted on all the Access Zones or Alarm Zones on all levels the Cardholder has privilege to perform overrides.

*For example:*

If an Alarm Zone override is performed at the reader of a 10 level elevator, and the Cardholder only has "Change to the Armed state" privilege to six of the levels, then only the Alarm Zones on those six levels will attempt to arm.

Depending on configuration, for the four levels that the Cardholder did not have privilege to arm the alarm zone, an "Access Override Denied" event will occur. This also results in an Access Denied tone sounding at the reader.

**Note:** If an HBUS Terminal is assigned as the reader for an elevator car, a Cardholder cannot perform an override using the function keys (Arm and Mode) keys at the terminal. However, double card overrides can still be performed, although not recommended.

**Important:**

* This is not the recommended setup, as overrides should be performed at the individual readers in each Access or Alarm Zone.
* While double card overrides can be performed at elevator car readers, it is not recommended because of the potential to accidentally override multiple Alarm Zone or Access Zone states.

### Alarm Zone override at a reader

This table summarises the effect of overriding an Alarm Zone at a local reader on a door and the privileges that are required. Where the override is performed at an elevator car reader, Alarm Zones on any level are armed or disarmed as shown, provided that the Cardholder has the required privilege for that level.

<table><thead><tr><th width="224">Action</th><th width="156">Alarm Zone (Before)</th><th width="150">Alarm Zone (After)</th><th>Privileges Required</th></tr></thead><tbody><tr><td>Double card badge</td><td>Disarmed</td><td>Armed</td><td>"Change to the Armed state" privilege for the Alarm zone.<br>Reader set to "Arm alarm zone" for double card overrides.</td></tr><tr><td>Double card badge</td><td>Armed</td><td>Armed</td><td>"Change to the Disarmed state" privilege for the Alarm Zone.<br>"Change to the Armed state" privilege for the Alarm zone.<br>Reader set to "Arm alarm zone" for double card overrides.</td></tr><tr><td>Single card badge</td><td>Armed</td><td>Disarmed</td><td>"Change to the Disarmed state" privilege for the Alarm Zone.</td></tr><tr><td>Arm and access method (Cardax IV T20 Terminal) or Arm and log on (HBUS Terminal)</td><td>Disarmed</td><td>Armed</td><td>"Change to the Armed state" privilege for the Alarm zone.</td></tr></tbody></table>

### Access Zone override at a reader

This table summarises the effect of overriding an Access Zone at a local reader on a door and the privileges that are required. Where the override is performed at an elevator car reader, the Access Zone state for any level is changed as shown, provided that the Cardholder has the required privilege for that level.

**Note:** You cannot perform an Access Zone override at a reader unless the Alarm Zone associated with the Access Zone is disarmed.

<table><thead><tr><th width="224">Action</th><th width="156">Access Zone (Before)</th><th width="150">Access Zone (After)</th><th>Privileges Required</th></tr></thead><tbody><tr><td>Double card badge</td><td>Scheduled</td><td>Mode 2</td><td>"Lock and unlock access zones" privilege for the Access Zone.<br>Reader set to "Override access zone" for double card overrides.</td></tr><tr><td>Double card badge</td><td>Mode 2</td><td>Scheduled</td><td>"Lock and unlock access zones" privilege for the Access Zone.<br>Reader set to "Override access zone" for double card overrides.</td></tr><tr><td>Mode and access method (Cardax IV T20 Terminal) or Mode and log on (HBUS Terminal)</td><td>Any</td><td>Mode 1, Mode 2 or Scheduled state, whichever is selected by the cardholder performing the override.</td><td>"Lock and unlock access zones" privilege for the Access Zone.</td></tr></tbody></table>

***

### Configuration

This procedure has been split into four, as follows. Follow the procedures that are appropriate for the configuration you require.

<details>

<summary>Configuring an Access Zone Override at a Reader</summary>

1. Click **Manage** from the menu bar, then **Access Groups**.

   The **Access Group** List Window opens (in [tree view](https://help.security.gallagher.com/knowledge-hub/configuration-client/introduction-to-command-centre/knowing-your-way-around/list-windows/tree-view.md)).
2. Open the relevant Access Group(s) for the people to have this privilege.
3. Click the **Privileges** tab.
4. Check the **Lock and unlock access zones** checkbox.

   This privilege enables members to override the state of an Access Zone from a reader.

   The Access Zones that the privilege applies to are listed on the **Access** tab of the Access Group.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-932a860a301f4cd28764a731b7ab978305c02e92%2Fprivileges_accesszone.png?alt=media)
5. Click the **OK** button.
6. Click **Configure** from the menu bar, then **Access Zones**.

   The **Access Zone** List Window opens (in [tree view](https://help.security.gallagher.com/knowledge-hub/configuration-client/introduction-to-command-centre/knowing-your-way-around/list-windows/tree-view.md)).
7. Open the Access Zone associated with the reader where these local overrides will be performed from.
8. Click the **Access Mode** tab.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-00b126aacdbbd188ecbc4c395a15e293894694ce%2Faczone_amode.png?alt=media)
9. The 'Cardholder Overrides' section of this screen determines what happens when a cardholder overrides this Access Zone. Otherwise the mode is determined by the Schedule.

   When performing overrides, you can select which state (Mode 1, Mode 2 or Scheduled) the Access Zone is overridden to. When performing double card overrides the Access Zone state changes between Mode 2 and the scheduled state with each successive override that is applied.

   The Display Name is viewed on the HBUS Terminal only. The Display Name enables you to describe the Access Mode, (e.g. After Hours). If using an HBUS Terminal, enter the Display Name for each Mode.

   Specify the required access modes for Mode 1 and Mode 2.
10. Click the **OK** button.
11. To configure the maximum time allowed between card badges or between pressing a function key and badging your card refer to *Configuring the Card Badge Time-out* (later in this section).
12. Do you intend using double card overrides?

    * If **no**, then this procedure is complete.
    * If **yes**, then go to *Configuring Double Card Overrides at a Reader* (later in this section).

    **Result**

    Cardholders belonging to this Access Group can now perform overrides of the Access Zones assigned to this Access Group from a local reader.

    **Hint:** If the Door has been configured with an exit Access Zone, the override is successfully performed on the entry Access Zone, however the door will remain locked, if the exit Access Zone Access Mode is set to secure. To ensure the lock status of the door follows the entry zone Access Mode, check the **Door lock status follows entry zone only** checkbox on the **Advanced** tab of the Door’s properties.

</details>

<details>

<summary>Configuring an Alarm Zone Override at a Reader</summary>

1. Click **Manage** from the menu bar, then **Access Groups**.

   The **Access Group** List Window opens (in [tree view](https://help.security.gallagher.com/knowledge-hub/configuration-client/introduction-to-command-centre/knowing-your-way-around/list-windows/tree-view.md)).
2. Open the relevant Access Group(s) for the Cardholders to have this privilege. This Access Group must contain the Access Zone associated with the Alarm Zone that you want to provide override privilege for.
3. Click the **Privileges** tab.

   Check the **Change to the Armed state** checkbox if you want to provide the privilege to arm alarm zones.

   Check the **Change to the Disarmed state** checkbox if you want to provide the privilege to disarm alarm zones.

   The privilege applies to Alarm Zones associated with the Access Zones listed on the **Access** tab. It is also confined to the time-frames in which access is allowed to the Access Zone, as specified in the associated Schedule.

   **Note:** The privilege applies to the Alarm Zones listed in the Alarm Zones tab of this Access Group, if you are performing the override at a terminal.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-54075bacb250323ebe71151b330053598b08fced%2Fprivileges_almzone.png?alt=media)
4. Click the **OK** button.
5. To configure the card badge time-out when performing the override, refer to *Configuring the Card Badge Time-out* (later in this section). This is the maximum time allowed between card badges, when performing a double card override, or between pressing a function key and badging your card.
6. Do you intend using double card overrides?

   * If **no**, then this procedure is complete.
   * If **yes**, then go to *Configuring Double Card Overrides at a Reader* (later in this section).

   **Result**

   Cardholders belonging to this Access Group can now perform overrides of the Alarm Zones associated with the Access Zones assigned to this Access Group from a local reader.

</details>

<details>

<summary>Configuring the Card Badge Time-out</summary>

This procedure configures the card swipe time-out at a reader installed at a door or in an elevator car.

**Note:** The Arm and Mode override card time-outs on an HBUS Terminal are configured on the **Welcome Screen** tab of the HBUS Terminal FT item.

1. Open the **Door** List Window (for doors) or the **Elevator Car** List Window (for elevator cars).
2. Open the door or elevator car which the reader, (i.e. the reader where the override will be performed from), is connected to.
3. Click the **Advanced** tab.
4. Are you configuring the local override for a door or elevator car?

   * If it is at a **door**, refer to this step and skip Step 5.
   * If it is at an **elevator car**, refer to Step 5.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-d7930e7f8f83713e429ac4c6d02b6eba9b46df85%2Fbadgedoor.png?alt=media)

   Enter the number (in seconds) in the **Second card (for two-card entry) must be swiped** field for the time required between the two card badges, or between pressing a function key then badging your card.

   **Note:** Altering this also modifies the second card swipe time for visitors and [*Dual Authorisation*](https://help.security.gallagher.com/knowledge-hub/configuration-client/glossary-of-terms.md#dual-authorisation) mode.
5. Enter the number (in seconds) in the **Card swipe timeout** field for the time required between the two card badges, or between pressing a function key then badging your card.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-7cd434acaaf7fe40881cae2bb5b2a859830cded4%2Felevatorcar_advanced.png?alt=media)
6. Click the **OK** button.

   **Result**

   The configured card badge time-out will be applied to any overrides performed at the door or elevator car.

</details>

<details>

<summary>Configuring Double-Card Overrides at a Reader</summary>

1. Open the Property page for the reader(s) associated with the door, (i.e. as specified on the **Entry Zone** and **Exit Zone** tabs of the Door Properties).

   **Note:** If you are configuring an override at an Elevator Car, select the reader associated with the Elevator Car (i.e. as specified on the **Connections** tab of the Elevator Car Properties).
2. Click the **Advanced** tab.
3. Click either the **Override access zone** or the **Arm alarm zone** radio button, depending on whether you want the double card override to override the state of the Access Zone or arm the Alarm Zone associated with the Access Zone.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-91bb0a789634999dc72191bf3153c5847f098d4f%2Fadvanced_hbusterminal.png?alt=media)
4. Click the **OK** button.

   The double card override feature is enabled.
5. Repeat this procedure for each Door or Elevator Car associated with a reader from which you want to perform double card overrides.

   **Result**

   Cardholders with the appropriate override privilege can now override the Access Zone state or Alarm Zone state (whichever was configured) at this reader using a double card override.

   **Note:** The double card override feature is not supported whilst an Access Zone is in Dual Authorisation mode.

</details>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/site-monitoring/status-and-overrides/configuring-local-overrides-at-card-readers.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
