> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/site-management/operator-privileges/which-operator-privileges-you-require/override.md).

# Override

### Disable Workstation

An operator with "Disable Workstation" privilege in a division can disable a Workstation in that division.

### Disable Workstation Routing

An operator with "Disable Workstation Routing" privilege in a division can perform the following in the Command Centre Client:

* Move any Workstation Routing item in that division to the "Disabled" state, and
* Move any Workstation Routing item in that division out of the "Disabled" state to either of the other states.

### Enable Workstation

An operator with "Enable Workstation" privilege in a division can enable a Workstation (that has been disabled) in that division.

### Maintenance Override

An operator with "Maintenance Override" privilege in a division can perform the following:

* Override to "Shunt", "Unshunt", "Isolate" or "De-isolate" any Input in that division.
* Override to "Shunt" or "Unshunt" any Fence Zone in that division, (i.e. the deterrent is still active and will respond to commands, but all warning or alarm events are ignored).
* Override to "On" or "Off" any Fence Zone in that division.
* Override to “High Voltage” or “Low Feel” for any Fence Zone connected to an F31, F32, F41, F42 or F22 Fence Controller in that division.
* Override to “Maintenance Mode” or “Walk Test Mode” any Z10 Tension Sensor Group in that division.
* Override to "Reset", "Shunt" or "Unshunt" specific\* hardware Command Centre items in that division.
* Override to "Shunt" or "Unshunt" specific\*\* hardware Command Centre items in that division.
* Override to "Reset", "Disable Communication", "Enable Communication", "Enable WWW Connections" or "Cancel WWW Override" any Controller in that division.
* Override to "Renew DHCP Settings", "Revalidate certificate" Controller 6000 in that division.
* Override to "Use secondary ethernet" or "Cancel use secondary ethernet" Controller 6000's only (if dual ethernet is enabled).
* Override to "Reset Reader Keys" for Cardax IV Readers, with either "View Site" or "Edit Site" privilege also.
* Override any Logic Block in that division to "On", "Off" or "Reset Logic".
* Disable or enable communication with a remote server.
* Reset replication with a remote server.
* Cancel overrides that can be established with this privilege.

Operator must be able to "View" the items that they are wanting to override so they can access the **Status and Overrides** tab on the properties page in order to perform the override/shunt.

\* Override to "Reset", "Shunt" or "Unshunt" the following hardware Command Centre items in that division:

{% columns %}
{% column %}
HBUS 8-In 2-Out Door Module

HBUS 8-In Board

HBUS 8-In 4-Out Board
{% endcolumn %}

{% column %}
HBUS 16-In 16-Out Board

HBUS Terminal

HBUS Alarms Only Terminal
{% endcolumn %}

{% column %}
HBUS F22 Fence Controller

HBUS F31/F32/F41/F42 Fence Controller
{% endcolumn %}
{% endcolumns %}

\*\* Override to "Shunt" or "Unshunt" the following Command Centre items in that division:

{% columns %}
{% column %}
Z10 Tension Sensor Group
{% endcolumn %}

{% column %}
Elevator HLI
{% endcolumn %}
{% endcolumns %}

### Override

An operator with "Override" privilege in a division can perform the following:

* Override Access Zone state for a specified time, until the next scheduled change or until the override is cancelled, for any Access Zone in that division for any of the twelve possible Access Zone states.
* Forgive cardholders in that division (to whom they also have "View cardholder" privilege, or any higher privilege that enables them to view the cardholder's properties) anti-passback violations, for any access zone in that division.
* Forgive all cardholders anti-passback violations for any Access Zone in that division.
* Perform a Lockdown or Cancel a Lockdown on an Access Zone in that division.
* Override the zone count for any Access Zone in that division.
* Override an Output (to "On", "Off", or "Pulse") for a specified time or until the next scheduled change, for any Output in that division.
* Override an Alarm Zone state (to "Armed", "Disarmed", "User1" or "User2"), for any Alarm Zone in that division.
* Override an Interlock Group in that division ("Enable" or "Disable" the Interlock Group).
* Override a lift car to Go to Floor.
* Cancel stateful overrides that can be established with this privilege.

  **Note:** If an override is selected that cannot be cancelled, (i.e. shunt or unshunt), then there is no option for the user to Cancel the override.

This privilege also allows an operator to view any of the items that they can override with this privilege (except cardholders).

### Override up to Medium Priority

The "Override up to Medium Priority" privilege allows the same privilege set as the "Override" privilege (see above), but the Operator can only override active alarms up to (and including) ‘Medium Priority’ (as long as doing so will not cause any alarms).

### Override - Lock Door

An operator with "Override - Lock Door" privilege can manually lock a Half-Cycle lock type Door. A Half-Cycle door will remain unlocked after access is granted until either it is opened and shut or the Lock Door override is used.

### Override - Open Door

An operator with "Override - Open Door" privilege in a division can unlock a locked door for a short time, for any Controller door in that division.

### Override - Open Locker

An operator with "Override - Open Locker" privilege in a division can open and/or isolate Lockers.

### Override Card Status

An operator with "Override Card Status" privilege in a division can perform the following:

* Change the state of a card that is in a Permanently Disabled state.
* Allow a card to be created with the same details (card number, facility code, issue level) as a card that is in a 'Stolen', or other Permanently Disabled state.

### Run Macros

An operator with "Run Macros" privilege in a division can perform the following:

* View the properties of Macros in that division.
* Run a Macro in that division.

### Schedule & Run Macros

An operator with "Schedule & Run Macros" privilege in a division can perform the following:

* View the properties of Macros in that division.
* Edit the scheduled run times for a Macro in that division (add or remove scheduled run times).
* Run a macro in that division.

### Send Broadcast Notifications

When added to a Viewer, an operator with the "Send Broadcast Notifications" privilege can view, edit before sending and send the same email or SMS message (Short Message Service) to many Cardholders at once in the Command Centre Client.

### Use Workstation Routing

An operator with "Use Workstation Routing" privilege in a division can move any Workstation Routing item in that Division between the non-Disabled states, in the Command Centre Client.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/site-management/operator-privileges/which-operator-privileges-you-require/override.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
