> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/site-installation/hardware/creating-controllers/configuring-a-controller-for-dhcp.md).

# Configuring a Controller for DHCP

### Introduction

DHCP (Dynamic Host Configuration Protocol) allows sites to use their own DHCP service to assign IP addresses to their controllers automatically, without physically needing to be at the controller. This procedure describes how to configure DHCP.

### Prerequisites

* Ensure that your controller firmware has been updated to the latest version.

  Refer to either **3E2203 Release Note Controller 6000 vCRx.xx.xxxxxx.pdf** or **3E5746 Release Note Controller 7000 vCRx.xx.xxxxxx.pdf** for details. These documents are located in the `'Documentation'` directory of the Command Centre installation files.
* For DHCP to work, its configuration must include certain parameters before the Controller will trust the DHCP lease offered to it.

  Refer to **DHCP Server Configuration.pdf** for detailed instructions. This document is located in the `'Utilities\DHCP'` directory of the Command Centre installation files.

### Procedure

1. Click **Configure** from the menu bar, then **Hardware**.

   The **Hardware** List Window opens (in [tree view](https://help.security.gallagher.com/knowledge-hub/configuration-client/introduction-to-command-centre/knowing-your-way-around/list-windows/tree-view.md)).
2. Are you configuring a new Controller for DHCP, or an existing already configured Controller?

   <table><thead><tr><th width="112">If...</th><th>then...</th></tr></thead><tbody><tr><td>new,</td><td><p>create the new Controller in Command Centre, as follows:</p><ol><li>Right-click <strong>New</strong> > <strong>Controllers</strong> and the appropriate Controller type, (i.e. <strong>Controller 7000, 7000 Single Door</strong> or <strong>6000</strong>).<br>The Controller Properties window opens to the <strong>General</strong> tab by default.</li><li>Enter the Controller name, short name and description in the <strong>Name</strong>, <strong>Short Name</strong> and <strong>Description</strong> fields.</li><li>Select the appropriate division for the Controller from the <strong>Division</strong> drop-down list.</li><li>Click the <strong>Network</strong> tab.</li><li>Enter the controller’s MAC Address in the MAC Address field, then go to step 3.</li></ol></td></tr><tr><td>existing,</td><td><strong>Right click</strong> the Controller you want to configure DHCP for, and select <strong>Properties</strong>.<br>The Controller Properties window opens to the <strong>General</strong> tab by default.</td></tr></tbody></table>
3. Click the **Network** tab.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-f5de1ab4c982a981a7b062f5b82ee855cadea27d%2Fdhcp_c6000_networktab.png?alt=media)
4. Configure the settings on this screen as appropriate.

   <table><thead><tr><th width="150.11114501953125">If you want to enable DHCP for...</th><th>then...</th></tr></thead><tbody><tr><td>IPv4,</td><td>tick the <strong>Enable custom DHCP</strong> checkbox.<br>The <strong>IP Address</strong>, <strong>Subnet</strong> and <strong>Gateway</strong> fields deactivate, and a <strong>Valid until</strong> section appears and displays 'Unknown'.<br><br><strong>Note:</strong> After you have clicked <strong>Apply</strong>, the <strong>Valid until</strong> value should change from 'Unknown' to a date and time. This date and time is the fixed length of the lease determined by DHCP settings. If <strong>Valid Until</strong> still displays 'Unknown', check that DHCP services are running and configured appropriately.</td></tr><tr><td>IPv6,</td><td><ol><li>Ensure the <strong>Enable custom DHCP</strong> checkbox is unticked.</li><li>Tick the <strong>Enable IPv6</strong> checkbox.<br>The <strong>Network Prefix</strong> and <strong>Address</strong> fields activate.</li><li>Tick the <strong>Enable custom DHCPv6</strong> checkbox.<br>The <strong>Network Prefix</strong> and <strong>Address</strong> fields deactivate.</li></ol></td></tr><tr><td>IPv4 and IPv6,</td><td><ol><li>Tick the <strong>Enable custom DHCP</strong> checkbox.<br>The <strong>IP Address</strong>, <strong>Subnet</strong> and <strong>Gateway</strong> fields deactivate and a <strong>Valid until</strong> section appears and displays 'Unknown'.<br><br><strong>Note:</strong> After you have clicked <strong>Apply</strong>, the <strong>Valid until</strong> value should change from 'Unknown' to a date and time. This date and time is the fixed length of the lease determined by DHCP settings. If <strong>Valid Until</strong> still displays 'Unknown', check that DHCP services are running and configured appropriately.</li><li>Tick the <strong>Enable IPv6</strong> checkbox.<br>The <strong>Network Prefix</strong> and <strong>Address</strong> fields activate.</li><li>Tick the <strong>Enable custom DHCPv6</strong> checkbox.</li></ol></td></tr></tbody></table>
5. Click **OK** to exit and save your changes.

   Click **Cancel** to exit without saving your changes.

   Click **Apply** to save your changes and stay in this window.
6. Refer to the following table to complete your configuration.

   What Controller are you using?

   <table><thead><tr><th width="229">If a...</th><th>then...</th></tr></thead><tbody><tr><td>a deployed and online controller running v7.80 (or later) firmware,</td><td>no further action is required.<br>The controller will automatically switch to DHCP as soon as it receives its new configuration from Command Centre.</td></tr><tr><td>a new Controller,</td><td><ol><li>Power on the Controller.</li><li>When the controller Run LED flashes to indicate normal operation, (i.e. 500ms on, 500ms off), turn dip switches 2 and 3 off.<br><br><strong>Note:</strong> Once you enable DHCP, and the controller has successfully been assigned an IP address, several fields will be populated on the <strong>Network</strong> tab depending on your DHCP configuration.</li></ol></td></tr></tbody></table>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/site-installation/hardware/creating-controllers/configuring-a-controller-for-dhcp.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
