> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/site-installation/hardware/configuring-eol-resistors-for-devices.md).

# Configuring EOL Resistors for devices

### Introduction

This procedure describes how to configure End-of-line (EOL) resistances for a device in Command Centre. EOL resistances are configurable via Command Centre for the following hardware devices:

* Gallagher Controller 6000s
* Gallagher Controller 7000s
* Gallagher Controller 7000 Single Door
* Gallagher HBUS I/O Interfaces
* Gallagher HBUS F31/F32/F41/F42 Fence Controllers
* Gallagher HBUS F22 Fence Controllers
* Gallagher QuickSwitch ME1502 Boards

This functionality makes it easier for installers to add Command Centre devices to sites whose input EOL resistor networks are suited to work with legacy Gallagher or competitors equipment.

**Note:** This procedure assumes that the device you want to configure the EOL resistances for has already been created in Command Centre. However, if you have not yet created the device, refer to the appropriate procedure first, (i.e. [Creating Controllers](https://help.security.gallagher.com/knowledge-hub/configuration-client/site-installation/hardware/creating-controllers.md) or [Creating Devices](https://help.security.gallagher.com/knowledge-hub/configuration-client/site-installation/hardware/creating-devices.md)).

### Procedure

1. Click **Configure** from the menu bar, then **Hardware**.

   The **Hardware** List Window opens (in [tree view](https://help.security.gallagher.com/knowledge-hub/configuration-client/introduction-to-command-centre/knowing-your-way-around/list-windows/tree-view.md)).
2. Highlight the required device, (i.e. the one you want to configure the EOL resistance for).
3. **Right click** and select **Properties**.
4. Click the **EOL Resistors** tab.

   The following example is the EOL Resistors tab for an F22 Fence Controller.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-22d77764527aa8c377a73616d50c0e92fdbd3bad%2Ff22_eolresistorstab.png?alt=media)

   This tab provides an **EOL Resistances** drop-down list of pre-calculated sets of resistor values for the installer to select a value from, and a circuit diagram to show which resistors are configured with which values.

   **Note:** For most devices, this tab only provides a drop-down list of EOL resistor values for **2, 3 or 4-state devices**. However, for Controller 6000s, Controller 7000s and HBUS I/Os, in addition to resistor values for **2, 3 or 4-state devices**, it also has a drop-down list of resistor values for **6-state devices**, as shown below:

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-f8c212748f5d223af806e4104c0ce89323037254%2Fftc6000_eolresistorstab.png?alt=media)

   Each set of resistor values is one of the following:

   <table><thead><tr><th width="240">Set of resistor values</th><th>Provides...</th></tr></thead><tbody><tr><td>6 state Inputs using 3 resistors</td><td>for masked, fault, tamper open-circuit, tamper short-circuit, open and closed states</td></tr><tr><td>4 state Inputs using 2 resistors</td><td>2 kinds of tamper detection</td></tr><tr><td>3 state Inputs using 1 resistor</td><td>only 1 kind of tamper detection depending on NO or NC selection (Normally Open/Closed)</td></tr><tr><td>2 state Inputs using no resistors</td><td>no tamper detection</td></tr></tbody></table>
5. Select the required resistor values from the drop-down list.

   **Note:** The values you select will apply to all the Inputs on that particular device. In the case of Controllers, the resistor values will apply to the Inputs on the Controller itself, and not any attached devices.
6. Click **OK**.

### Result

EOL resistance has been configured for a device.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/site-installation/hardware/configuring-eol-resistors-for-devices.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
