> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/licensable-features/piv-card-support/open-supervised-device-protocol-osdp-veridt-stealth-piv-readers.md).

# Open Supervised Device Protocol (OSDP) Veridt Stealth PIV Readers

### Introduction

Open Supervised Device Protocol (OSDP) replaces the Wiegand legacy protocol, and allows security devices such as card readers, controllers and I/O boards to talk to each other through a bi-directional RS485 channel.

The Open Supervised Device Protocol (OSDP) Veridt Stealth PIV Reader provides three factor authentication, (i.e. Card, PIN and Fingerprint), if required.

OSDP Veridt Stealth PIV Readers should only be assigned to Gallagher PIV Controller 6000s. We recommend only using one Veridt Reader per RS-485 Bus.

### Functionality not supported

The following functionality is NOT supported on OSDP Veridt Stealth PIV Readers:

* PIN to PACS
* PIN is User Code
* Code only code
* Duress
* PIN's mode when the reader is on an Elevator Car.

  **Note:** If the Access zone is in "Secure - No PIN" mode, but Veridt Reader access mode mapping is Two Factor, a PIN will be requested for access.
* Double card overrides will work on the Veridt Reader using proximity PIV cards. Not supported with PINs mode or when card inserted.

### Known Issues

* Veridt Readers will reset and generate a "not responding" alarm when a PIN is not entered or just the **#** key is entered for the second consecutive time after inserting the card.
* When a non-BIO Veridt Reader is configured as Three Factor, it will respond with "Access Denied" after entering the PIN, and a Fingerprint Mismatch event will be generated in Command Centre.
* When power cycling a Veridt Reader on Address 1, the baud rate will change to 9600.
* Changing Address will set the baud rate to the default of 9600.
* Veridt Readers may restart when PIV Contactless cards are presented immediately at the end of every access transaction.

Select the item below that you require further detail on:

![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-f30c70c9dfd07493527af00bd979539606de5d30%2Ftopiclink.png?alt=media) [Configuring an OSDP Veridt Stealth PIV Reader](https://help.security.gallagher.com/knowledge-hub/configuration-client/licensable-features/piv-card-support/open-supervised-device-protocol-osdp-veridt-stealth-piv-readers/configuring-an-osdp-veridt-stealth-piv-reader.md)

![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-f30c70c9dfd07493527af00bd979539606de5d30%2Ftopiclink.png?alt=media) [Assigning an OSDP Veridt Stealth PIV Reader to a Gallagher PIV Controller 6000](https://help.security.gallagher.com/knowledge-hub/configuration-client/licensable-features/piv-card-support/open-supervised-device-protocol-osdp-veridt-stealth-piv-readers/assigning-an-osdp-veridt-stealth-piv-reader-to-a-gallagher-piv-controller-6000.md)

### In This Section

* [Configuring an OSDP Veridt Stealth PIV Reader](https://help.security.gallagher.com/knowledge-hub/configuration-client/licensable-features/piv-card-support/open-supervised-device-protocol-osdp-veridt-stealth-piv-readers/configuring-an-osdp-veridt-stealth-piv-reader.md)
* [Assigning an OSDP Veridt Stealth PIV Reader to a Gallagher PIV Controller 6000](https://help.security.gallagher.com/knowledge-hub/configuration-client/licensable-features/piv-card-support/open-supervised-device-protocol-osdp-veridt-stealth-piv-readers/assigning-an-osdp-veridt-stealth-piv-reader-to-a-gallagher-piv-controller-6000.md)


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/licensable-features/piv-card-support/open-supervised-device-protocol-osdp-veridt-stealth-piv-readers.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
