> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/salto-lock-interface/space-site-configuration/salto-wireless-rf-devices.md).

# Salto wireless RF devices

### Introduction

The Salto network includes items like encoders, gateways, radio frequency (RF) nodes, CU4200 nodes, online doors, and control units. These are added and managed in the Salto application.

**Note:** Salto ProAccess SPACE supports Salto RF mode 2 only. If using Salto devices that use RF mode 1, please contact your Gallagher representative, as these may need to be replaced.

### Procedure

This procedure is split into several smaller procedures to cover the whole process involved in configuring a wireless lock. The procedures, in the order they should be performed are:

* RF channels
* Viewing the Salto network
* Adding an RF gateway
* Adding an RF node

### RF channels

You can view the enabled channels for RF signals in the Salto software. To do so, select **System > General options > Devices**. There are 16 channels available and all of these are enabled by default. The frequency range of each channel is also displayed. You can disable a channel if required by clearing the checkbox for the channel and clicking **Save**.

If the site is already utilising wireless RF functionality, (e.g. for wireless internet, RFID applications, etc.) then you will need to carefully select the enabled channels, so that there is no, or minimal crossover of RF signal on site. The scan utility **inSSIDer.exe** which is free to download from the internet, can be used to detect clogged RF channels.

![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-5fd549edeeca3c7498c04e0c23a62ae3c2ffe8eb%2Frfchannels.png?alt=media)

How you know if there is RF crossover?

* It will likely not become apparent until you notice that certain RF escutcheons are either not properly communicating or events are being returned in 'bursts'.
* If there is another RF application utilising the frequencies required by locks or gateways, then the Salto hardware will retain the events/configuration until they are able to utilise the frequencies.

If you do find this type of behaviour on your site, you will need to ascertain what Site Scan Channels are being utilised by non-Salto applications or hardware on site, and de-select those enabled channels accordingly within Salto. This means that the Salto gateways will only use the channels specified, and communication should be constant.

### Viewing the Salto network

You can view the list of Salto network items by selecting **System > SALTO Network**.

The Salto Network screen displays a list of all network items that have been added and are currently connected to the system.

![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-63255ffa1f2d30aab6e9693f000c60331b50d2f9%2Fsaltonetwork.png?alt=media)

The information is displayed in four different filtered views:

<table><thead><tr><th width="168">View</th><th>Description</th></tr></thead><tbody><tr><td>All</td><td>This view shows all of the gateways, encoders, and control units on the system.</td></tr><tr><td>Gateways</td><td>This view shows RF gateways. When you click the triangular Expand icon on the left-hand side of gateway names, all of the items to which they are connected are displayed. You can view all of the RF nodes and online RF (Salto) access points connected to each RF gateway and all RF gateway nodes.</td></tr><tr><td>Encoders</td><td>This view shows the encoders on the system</td></tr><tr><td>Control units</td><td>This view shows online control units (UBOX900003, CU50ENSVN and CU42E0).</td></tr></tbody></table>

### Adding an RF gateway

Gateways are hardware devices that provide a link between networks that use different base protocols. RF gateways allow data to be transmitted from the system to the Salto RF locks, and from the RF locks to the system. RF gateways control RF nodes.

You must physically connect RF nodes to an RF gateway using an RS485 cable to establish communication between the RF nodes and the RF gateway. You must also connect RF nodes and RF gateways in the Salto application so the system can show which nodes and gateways are connected.

1. Select **System > Salto Network**.

   The Salto Network screen is displayed.
2. Click **Add Network Device**.

   The Add network device dialog box is displayed.
3. Select **RF gateway** from the drop-down list, then click **OK**.

   The RF gateway information screen is displayed.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-2d4364ecac22bb3ef1cd22958124642fbb8c041e%2Fgateway.png?alt=media)
4. Enter a name for the RF gateway in the **Name** field.
5. Enter a description for the RF gateway in the **Description** field, if required.
6. Type the media access control (MAC) address in the **MAC address** field.

   **Note:** This is usually displayed on the Ethernet board of the RF gateway.
7. Select either the **Network name (DHCP)** or **IP address** option.

   If you select the **Network name (DHCP)** option, this automatically assigns an IP address to the RF gateway. A Dynamic Host Configuration Protocol (DHCP) server and a DNS are required for this option. If you select the **IP address** option, you must type a static IP address in the field.
8. To address the Gateway RF2, connect the Gateway to the LAN (do not use a crossed cable). Press the **CLR** button on the Gateway RF2 circuit board for several seconds until the LED turns orange.
9. Using a Web Browser, access the IP address **192.168.0.234** and enter the IP address of the Gateway RF2 and select the **Static** Address configuration radio button.

   To ensure you can communicate to the Gateway RF2 set your configuration PC to an IP address of **192.168.0.1**.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-c7dfd19d73cca148bc361f9b8f031d5dcfc57645%2Fsalto_webservice_1.png?alt=media)
10. Ensure the LED is flashing on the Gateway RF2 circuit board, then click the **Send** button. The ‘Configuration successfully sent’ screen displays. The IP address is assigned and the device has been initialised at the same time.

    ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-9d8964b6b5079fe44a9c4c63ac24caf9efc2cf0d%2Fsalto_webservice_2.png?alt=media)

    **Note:** Gateway RF2s are compatible with PoE routers. For more information consult the Salto Gateways technical documentation.
11. Click **Add/Delete** in the RF Nodes panel.

    The Add/Delete dialog box, showing a list of RF nodes is displayed.

    The Add/Delete dialog box only displays RF nodes if you have already added them to the system. You can also connect RF nodes to RF gateways when you add RF nodes to the system.
12. Select the required RF node in the left-hand panel and click the chevron.

    The selected RF node is displayed in the right-hand panel.

    **Note:** You can hold down the Ctrl key while clicking the RF nodes to make multiple selections. You cannot add RF nodes that already belong to another gateway.
13. Click **Accept**.

    The selected RF node is displayed in the RF Nodes panel.
14. Click **Save**.

### Adding an RF node

RF nodes are network connection points that are physically connected to an RF gateway using an RS485 cable. This establishes communication between the RF nodes and the RF gateways. In the Salto application you must connect RF nodes to RF gateways, and RF access points to RF nodes. This means that the system can show which items are connected.

**Note:** You must select **Online RF (SALTO)** in the Connection Type panel on the Door or Room information screen to define a door as an RF access point.

1. Select **System > SALTO Network**.

   The SALTO Network screen is displayed.
2. Click **Add Network Device**.

   The Add network device dialog box is displayed.
3. Select **RF node** from the drop-down list, then click **OK**.

   The RF node information screen is displayed.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-afb1b37f2c10aa1432a50cdf1b09539074f378df%2Frfnode.png?alt=media)
4. Type a name for the RF node in the **Name** field.
5. Type a description for the RF node in the **Description** field.
6. Type the MAC address of the antenna in the **MAC address** field.
7. Select the RF gateway to which you want to connect the RF node from the **Connected to** drop-down list. The default option is **None**.
8. Click **Add/Delete** in the RF Access Points panel.

   The Add/Delete dialog box, showing a list of RF access points is displayed.

   The Add/Delete dialog box only displays RF access points if you have already defined doors as RF access points by selecting **Online RF (SALTO)** in the Connection Type panel on the Door or Room information screens. You can also connect online RF (SALTO) doors to RF nodes by using the **Connected to** field on the Online RF information screen.
9. Select the required RF access point in the left-hand panel and click the chevron.

   The selected RF access point is displayed in the right-hand panel.

   **Note:** You can hold down the Ctrl key while clicking the RF access points to make multiple selections. You cannot add RF access points that already belong to another RF node.
10. Click **Accept**.

    The selected RF access point is displayed in the RF Access Points panel.
11. Click **Save**.

    **Note:** RF gateways have a mini node connected to them. You must add this node in the Salto application by following the procedure above.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/salto-lock-interface/space-site-configuration/salto-wireless-rf-devices.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
