> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/open-supervised-device-protocol-osdp-integration/assigning-an-osdp-compliant-reader-to-a-gallagher-controller.md).

# Assigning an OSDP Compliant Reader to a Gallagher Controller

### Introduction

This procedure describes how to assign an Open Supervised Device Protocol (OSDP) compliant reader, (i.e. either a **OSDP Reader** or **Morpho Biometric Reader** type in Command Centre) to a Gallagher Controller.

**Important:** It is recommended you set up the initial connection between a Controller and reader in a secure environment, i.e. connection is made secure via physical security, such as controller/reader are connected via simple short cable. The secure connection is asserted to both the controller and reader by setting the devices into installation mode. For the reader this means using the manufacturer's defined method, and for the controller it occurs automatically when the reader is configured for the first time on that controller, or when a **Re-initialise encryption** override is performed.

### Procedure

1. Click **Configure** from the menu bar, then **Hardware**.

   The **Hardware** List Window opens (in [tree view](https://help.security.gallagher.com/knowledge-hub/configuration-client/glossary-of-terms.md#tree-view)).
2. Highlight the Controller you want to assign the new OSDP or Morpho Biometric Reader to.
3. **Right click** and select **Properties.**

   By default the **General** tab displays.
4. Click the **Setup** tab.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-41026268edbbbb6eca082f4c9274f9f287843d4a%2Fosdp_controller6000setuptab.png?alt=media)
5. In the Hardware section of this screen, select the 'OSDP' option from the **RS-485 Bus 1** and/or **RS-485 Bus 2** drop-down lists as appropriate.

   Depending on which RS-485 Bus option(s) you selected 'OSDP' for, an **OSDP Devices** and/or **OSDP Devices 2** tab appears, allowing you to add up to 16 OSDP Readers and/or Morpho Biometric Readers to the Bus port on this Controller.

   **Note:**

   * **Controller 6000:** Supports up to 16 OSDP and/or Morpho Biometric readers, split across runs - maximum 16 readers per run.
   * **Controller 7000:** Supports up to 32 OSDP and/or Morpho Biometric readers, split across runs - maximum 16 readers per run.
6. Click the **OSDP Devices** tab.

   ![](https://3000903572-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FfCvaxj3suxNBzdwQndVT%2Fuploads%2Fgit-blob-106ba4df322895d76727e2388884ceb9cf1d25d6%2Fosdp_controller6000_osdpdevicestab.png?alt=media)
7. From the **Hardware** List Window, select the OSDP Readers and/or Morpho Biometric Readers attached to this Bus. Drag and drop each Reader into the grid on the **OSDP Devices** tab.
8. Pair the item with the device by selecting the appropriate reader from the grid and entering the address into the **Configured Address** field below. (Address Range = 0 - 126)
9. If you want to change the device address, select the appropriate reader from the grid and enter an address into the **Device Address** field below. Click the **Change Address** button to push the configuration. (Address Range = 0 - 126)

   **Note:** The Change Device Address controls will be disabled if the selected device's status is offline, unknown or unconfigured.
10. Click **OK** to exit and save your changes.

    Click **Cancel** to exit without saving your changes.

    Click **Apply** to save your changes and stay in this window.

### Result

An OSDP Reader or a Morpho Biometric Reader has been created and it has been assigned to a Gallagher Controller. As a result, the following occurs:

* the Reader will display within the Hardware List Window.
* on the **Connections** tab of the Reader, the Gallagher Controller name will appear in the **Connected to** field.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/integrated-systems/open-supervised-device-protocol-osdp-integration/assigning-an-osdp-compliant-reader-to-a-gallagher-controller.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
