> For the complete documentation index, see [llms.txt](https://help.security.gallagher.com/knowledge-hub/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.security.gallagher.com/knowledge-hub/configuration-client/appendices/xyz-event-mappings.md).

# XYZ Event Mappings

### Introduction

This topic provides a list of all the Event Groups and Event Types in the Gallagher Command Centre system. For Contact ID, the **XYZ** Event Codes have been mapped to an existing Event Group. In the table below, the **XYZ** Event Codes are displayed in **"bold"** print under the relevant Event Group.

See also [CCC Identifiers](https://help.security.gallagher.com/knowledge-hub/configuration-client/appendices/ccc-identifiers.md) for a list of what **CCC** will be sent when a particular **XYZ** event occurs.

<table><thead><tr><th width="218" valign="top">Event Group</th><th valign="top">Event Type</th></tr></thead><tbody><tr><td valign="top">Access Denied<br><strong>421 - Access denied</strong></td><td valign="top">Access Challenged<br>Access change denied<br>Access Zone locked down<br>Alarm change denied<br>Bad 2nd authorization<br>Bad Level<br>Bad Second Card<br>Battery Too Low<br>Biometric - No Record Found<br>Biometric - Operation Timeout<br>Biometric - Unknown Error<br>Buffer Full<br>Card Blocked<br>Code Only Access Not Available while Alarms set<br>Door in emergency state<br>Exit Denied<br>Invalid Card Issue<br>Invalid Salto Card Issue<br>More than One Visitor<br>No 2nd authorization<br>No access at this time<br>No Escort<br>No Privacy Override Privilege<br>No Salto access at this time<br>No Salto Zone Privilege<br>No user code<br>No Zone Privilege<br>Not an escort<br>Passback Attempted<br>PIN Too Late<br>Repeated First Card<br>Terminal: Bad facility code<br>Terminal: Invalid issue<br>Terminal: No access<br>Terminal: PIN too late<br>Terminal: Unauthorized card<br>Unauthorised Card<br>Unauthorised Salto Card<br>Unknown Biometric<br>Wrong Facility Code<br>Zone Set - No Access</td></tr><tr><td valign="top">Alarm Transmission Failure<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Dial cycle completed without success<br>Periodic dialtone check failed</td></tr><tr><td valign="top">Alarm Transmission Warning<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Backup dialler failed<br>Dialler forwarding<br>Dialler gave up<br>Dialler link broken<br>Dialler no backup<br>Dialler no dial tone<br>Dialler no handshake<br>Dialler no modem<br>Dialler retry wait<br>Dialler transmit error</td></tr><tr><td valign="top">Alarm Zone Change Problem<br><strong>454 - Failed to close</strong></td><td valign="top">Arm failed<br>Code Only Set Already<br>Code Only Set Failed<br>Code Only Set Failed - Not User Mode<br>Code Only Set Failed - Offline<br>Input Set Fail<br>Set Failed - No Access<br>Set Failed - Offline<br>Terminal: Arm failed<br>Terminal: Force arm<br>Terminal: Isolate arm<br>Zone Set Already<br>Zone Set Failed<br>Zone Set Not User Mode</td></tr><tr><td valign="top">Card Error<br><strong>421 - Access denied</strong></td><td valign="top">Foreign Card<br>Illicit Card<br>Non High-Security Card<br>Terminal: Foreign card<br>Terminal: Illicit card</td></tr><tr><td valign="top">Card Event<br><strong>422 - Access report by User</strong></td><td valign="top">Accept First Card<br>Cancel Override<br>Card Cancelled<br>Card Exit Granted<br>Card Not Fully Updated<br>Card Updated<br>Code only No Entry<br>Door Access Granted<br>Door Free Access<br>Door Secure Access<br>Elevator Access Granted<br>Interlock Rules Prevented Code only Entry<br>Interlock Rules Prevented Entry<br>Level Access Granted<br>Level Not Selected<br>No Entry Taken<br>Override Mode 1<br>Override Mode 2<br>Salto Door Access Granted<br>Salto Door Closing Granted<br>Terminal: Active Alarm Acknowledgement<br>Terminal: Alarm Acknowledgement<br>Terminal: Auto-Logout<br>Terminal: Cancel override Fence Zone<br>Terminal: Logon<br>Terminal: Logout<br>Terminal: Override Off Fence Zone<br>Terminal: Override On Fence Zone<br>Terminal: Shunt<br>Terminal: Shunt Fence Zone<br>Terminal: Unshunt<br>Terminal: Unshunt Fence Zone</td></tr><tr><td valign="top">Card Trace<br><strong>422 - Access report by User</strong></td><td valign="top">Auto-Forgive on Exit From Site<br>Card Trace<br>Exit Allowed<br>Passback Allowed<br>Terminal: Card trace</td></tr><tr><td valign="top">Closed/On<br><strong>130 - Burglary</strong></td><td valign="top">Input Closed<br>Logic Block On<br>Output On</td></tr><tr><td valign="top">Command Centre Comms Interrupted<br><strong>330 - System Peripheral trouble</strong></td><td valign="top">Biometric Reader Comms Failed<br>Comms failed to Command Centre<br>Communications Server Offline<br>Controller Not Connected to Server Yet<br>Controller Offline<br>Event Server Offline<br>External System Offline<br>Intercom System endpoint offline<br>Remote Server Offline<br>Salto Server Offline<br>Service Offline</td></tr><tr><td valign="top">Copper Sync Detected<br><strong>131 - Perimeter</strong></td><td valign="top">Copper Sync Detected</td></tr><tr><td valign="top">Copper Sync Lost<br><strong>131 - Perimeter</strong></td><td valign="top">Copper Sync Lost</td></tr><tr><td valign="top">Door Not Locked<br><strong>426 - Access Door propped open</strong></td><td valign="top">Door Not Locked</td></tr><tr><td valign="top">Door Open Too Long<br><strong>426 - Access Door propped open</strong></td><td valign="top">Door Open Too Long</td></tr><tr><td valign="top">Door Status<br><strong>422 - Access report by User</strong></td><td valign="top">Daylight savings Time Adjustment<br>Door Opened<br>Door Re-secured<br>End of forced closing<br>PPD connection<br>Salto control unit updated<br>Start of forced closing</td></tr><tr><td valign="top">Duress<br><strong>121 - Duress</strong></td><td valign="top">Cardholder Duress<br>Code only DURESS<br>DURESS, Entry Denied<br>DURESS, Entry OK<br>Terminal: DURESS</td></tr><tr><td valign="top">Earth Warning<br><strong>131 - Perimeter</strong></td><td valign="top">Earth warning</td></tr><tr><td valign="top">External Event Group 0 - 29<br><strong>140 - General Alarm</strong></td><td valign="top">External Event 0 - 29</td></tr><tr><td valign="top">External System<br><strong>140 - General Alarm</strong></td><td valign="top">External System Online<br>Intercom System call connected at Command Centre<br>Intercom System call disconnected at Command Centre<br>Intercom System call received at Command Centre<br>Intercom System endpoint isolated<br>Intercom System endpoint normal mode of operation<br>Intercom System endpoint online<br>Intercom System endpoint remoted<br>SchindlerID Third-Party Database Online Interface Online</td></tr><tr><td valign="top">Fence Alarm<br><strong>131 - Perimeter</strong></td><td valign="top">Fence alert</td></tr><tr><td valign="top">Fence Low Feel Alarm<br><strong>131 - Perimeter</strong></td><td valign="top">Fence Low Feel Alert</td></tr><tr><td valign="top">Fence Low Feel Warning<br><strong>131 - Perimeter</strong></td><td valign="top">Fence Low Feel Warning</td></tr><tr><td valign="top">Fence Override High Voltage<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Overridden High Voltage</td></tr><tr><td valign="top">Fence Override Low Feel<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Overridden Low Feel</td></tr><tr><td valign="top">Fence Override Off<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Overridden off</td></tr><tr><td valign="top">Fence Override On<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Overridden on</td></tr><tr><td valign="top">Fence Shunted<br><strong>570 - Zone/Sensor bypass</strong></td><td valign="top">Fence shunted</td></tr><tr><td valign="top">Fence Warning<br><strong>131 - Perimeter</strong></td><td valign="top">Fence warning</td></tr><tr><td valign="top">Fence Zone High Voltage<br><strong>140 - General Alarm</strong></td><td valign="top">Fence High Voltage</td></tr><tr><td valign="top">Fence Zone HVplus<br><strong>140 - General Alarm</strong></td><td valign="top">Fence HVplus</td></tr><tr><td valign="top">Fence Zone Lockout<br><strong>140 - General Alarm</strong></td><td valign="top">Fence zone Lockout</td></tr><tr><td valign="top">Fence Zone Low Feel<br><strong>140 - General Alarm</strong></td><td valign="top">Fence Low Feel</td></tr><tr><td valign="top">Fence Zone Off<br><strong>140 - General Alarm</strong></td><td valign="top">Fence off</td></tr><tr><td valign="top">Fence Zone On<br><strong>140 - General Alarm</strong></td><td valign="top">Fence on</td></tr><tr><td valign="top">Forced Door<br><strong>423 - Forced Access</strong></td><td valign="top">Forced Door<br>Interlock Breach<br>Intrusion</td></tr><tr><td valign="top">HV Sync Pulse Absent<br><strong>140 - General Alarm</strong></td><td valign="top">HV Sync Pulse Absent</td></tr><tr><td valign="top">HVplus Escalation<br><strong>140 - General Alarm</strong></td><td valign="top">Fence Controller escalated to HVplus</td></tr><tr><td valign="top">Input Not Triggered<br><strong>380 - Sensor trouble</strong></td><td valign="top">Input not Triggered</td></tr><tr><td valign="top">Intercom Call<br><strong>140 - General Alarm</strong></td><td valign="top">Intercom Call Button Pressed</td></tr><tr><td valign="top">Inter-Controller Offline Monitoring<br><strong>140 - General Alarm</strong></td><td valign="top">Monitored Controller Offline</td></tr><tr><td valign="top">Invalid Logon<br><strong>461 - Wrong Code Entry</strong></td><td valign="top">Operator Logon Failed<br>Terminal: Invalid user code<br>Wrong Code only Code</td></tr><tr><td valign="top">Maintenance Failure<br><strong>393 - Maintenance Alert</strong></td><td valign="top">A configuration object could not be sent to the Controller because it was too big.<br>An Access Group has too many zones.<br>Archive Failed<br>Biometric Reader MIFARE Key Update Failed<br>Central Database Backup Failed<br>Controller bad diary action<br>Controller bad diary data<br>Controller bad event log<br>Controller bus message revision<br>Controller Database - cannot open<br>Controller Database - cannot read<br>Controller Database - cannot write<br>Controller Database - full<br>Controller dynamic RAM checksum test failed<br>Controller dynamic RAM test failed<br>Controller flash memory failure<br>Controller Incorrectly Configured<br>Controller invalid object<br>Controller message failed<br>Controller Network - bad authentication<br>Controller Network - bad protocol version<br>Controller Network - bad session message<br>Controller Network - GetHostByName failed<br>Controller Network - TCP failure<br>Controller Network - unrecognised application message.<br>Controller no part status<br>Controller Part - bad input<br>Controller Part - configuration failed<br>Controller Part - no configuration<br>Controller Part - no such type<br>Controller thread not responding<br>Download failed<br>Download Failure<br>Download Failure - file error<br>Download Failure - Timeout<br>Elevator HLI serial port not available<br>Event buffer corrupt<br>General Failure<br>Hardware Fault Detected<br>Image checksum failed<br>Initialisation Failed<br>Insufficient Reader Database Space<br>Invalid Certificate<br>License Expired - System is now read-only<br>Local Drive Critically Low Disk Space<br>Macro failed to run<br>Report failed<br>Re-sync Access Failed<br>SQL Server Database Critical Space Shortage<br>Unit Download Failure - Unit Offline<br>Unit MAC Error (Access)<br>Unit MAC Error (Level)<br>Unit MAC Error (Zone)<br>Unit Remote Diagnostic</td></tr><tr><td valign="top">Maintenance Mode<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Sensor Group in Maintenance Mode</td></tr><tr><td valign="top">Maintenance Warning<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Bad Packet<br>Bad unit type<br>Battery Low<br>Biometric Reader Tampered<br>Bulk Change Complete - Some Failures<br>Bulk Change One Item Failed<br>Command Centre Comms Interrupted<br>Command Centre Link - No Carrier<br>Command Centre Link Ceased<br>Controller alarm buffer overflow<br>Controller bad configuration parameter<br>Controller bad messge from unit<br>Controller bad packet from unit<br>Controller bad relay<br>Controller Database - missing<br>Controller disk space low<br>Controller event buffer Configuration Changed<br>Controller Incompatible configuration<br>Controller IP Address in use by another device<br>Controller IP Address Incorrect<br>Controller kill no part<br>Controller memory low<br>Controller missing calendar<br>Controller missing configuration parameter<br>Controller missing configuration section<br>Controller missing day<br>Controller Network - encryption policy mismatch<br>Controller Network - logon rejected<br>Controller Network - new key and certificate loaded<br>Controller Part - no such part<br>Controller property out of range<br>Controller shutdown no part?<br>Controller unhandled message<br>Controller unit command dropped<br>Controller unknown packet from unit<br>Controller Unknown version<br>Controller unrecognised name type<br>Controller WWW - send failed<br>Controller WWW - unauthorised<br>Deletion Conflict Detected<br>Dialler message lost<br>Download warning<br>Duplicate Card Detected<br>Duplicate Logon Name Detected<br>Duplicate Personal Data Detected<br>Duplicate User Code Detected<br>Elevator HLI bad reply<br>Elevator HLI protocol error<br>Event buffer deleted<br>General Warning<br>Hardware mismatch<br>Image lost<br>Invalid Command Line in Macro<br>Invalid User Account in Macro<br>License Warning - Devices required to maintain your license validity are not responding.<br>License Warning - License has expired<br>License Warning - License is not valid for this version of Command Centre.<br>License Warning - License limits have been exceeded.<br>Local Drive Low Disk Space Notification<br>Local Drive Low Disk Space Warning<br>Macro misconfiguration<br>Mains Power Failed<br>Network auth timeout<br>Network Overload<br>Network trans timeout<br>Replication Conflict Detected<br>SQL Server Database Space Shortage Notification<br>SQL Server Database Space Shortage Warning<br>Unexpected Controller reset<br>Unexpected request (special cardholder function)<br>Unit Bad Version<br>Unit Corrupt Setup<br>Unit Lost Setup<br>Unit MAC Error<br>Unit Obsolete Database<br>Unit Reset<br>Unit Start Refresh Ignored</td></tr><tr><td valign="top">Network Attack<br><strong>330 - System Peripheral trouble</strong></td><td valign="top">Network Attack</td></tr><tr><td valign="top">No Battery<br><strong>311 - Battery Missing/Dead</strong></td><td valign="top">No battery</td></tr><tr><td valign="top">Non-Card Door Unlock<br><strong>425 - Egress Granted</strong></td><td valign="top">Button Release Granted<br>Code only Access Granted<br>PPD Emergency Opening</td></tr><tr><td valign="top">Open/Off<br><strong>130 - Burglary</strong></td><td valign="top">Input Open<br>Logic Block Off<br>Output Off</td></tr><tr><td valign="top">Perimeter Attack<br><strong>131 - Perimeter</strong></td><td valign="top">Attack Detected</td></tr><tr><td valign="top">Point Not Tested<br><strong>612 - Point not tested</strong></td><td valign="top">Input not Tested</td></tr><tr><td valign="top">Power Critical<br><strong>311 - Battery Missing/Dead</strong></td><td valign="top">Unit stopped</td></tr><tr><td valign="top">Power Failure<br><strong>305 - System reset</strong></td><td valign="top">Power failed</td></tr><tr><td valign="top">Power out of Range<br><strong>302 - Low system battery</strong></td><td valign="top">Controller power high<br>Controller power low<br>Unit - power high<br>Unit - power low</td></tr><tr><td valign="top">Power Severe<br><strong>302 - Low system battery</strong></td><td valign="top">Unit going slow</td></tr><tr><td valign="top">Power Supply Failed<br><strong>301 - AC Loss</strong></td><td valign="top">Power supply failed</td></tr><tr><td valign="top">Power Warning<br><strong>302 - Low system battery</strong></td><td valign="top">Low battery</td></tr><tr><td valign="top">Primary ethernet link<br><strong>350 - Communication trouble</strong></td><td valign="top">Primary ethernet link failed</td></tr><tr><td valign="top">Primary ethernet link failed-over<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Secondary ethernet link failed-over</td></tr><tr><td valign="top">Repeated Login Failure<br><strong>421 - Access denied</strong></td><td valign="top">Terminal: Max bad logins</td></tr><tr><td valign="top">Secondary ethernet link<br><strong>350 - Communication trouble</strong></td><td valign="top">Secondary ethernet link failed</td></tr><tr><td valign="top">Security Breach<br><strong>341 - Exp. Module Tamper</strong></td><td valign="top">Terminal: Code Tampered<br>Terminal: Encryption Tampered</td></tr><tr><td valign="top">Sensor Abnormal<br><strong>131 - Perimeter</strong></td><td valign="top">Sensor Abnormal Tension - High<br>Sensor Abnormal Tension - Low<br>Sensor Offline<br>Sensor Power Low<br>Sensor Tension Overload</td></tr><tr><td valign="top">Sensor(s) Reporting Abnormal Tension<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Sensor Group Abnormal Tension</td></tr><tr><td valign="top">Service Mode<br><strong>140 - General Alarm</strong></td><td valign="top">Service Mode on</td></tr><tr><td valign="top">Shunted/Isolated<br><strong>570 - Zone/Sensor bypass</strong></td><td valign="top">Controller Bus Automatically Shunted<br>Controller Bus Shunted<br>Device Shunted<br>Input Isolated<br>Input Shunted<br>Sensor Group Shunted</td></tr><tr><td valign="top">State Unknown<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Logic items in unknown state</td></tr><tr><td valign="top">Tamper<br><strong>145 - Expansion module tamper</strong></td><td valign="top">Controller tampered (front)<br>Controller tampered (rear)<br>Input Break<br>Input Short<br>Input Tampered<br>Salto Door Tampered<br>Unit Tampered<br>Unit Tampered (Front)<br>Unit Tampered (Rear)</td></tr><tr><td valign="top">Temperature Critical<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Unit stopped - Temperature</td></tr><tr><td valign="top">Temperature out of HVplus range<br><strong>140 - General Alarm</strong></td><td valign="top">HVplus escalations disabled - high temperature</td></tr><tr><td valign="top">Temperature Out of Range<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Temperature too high<br>Temperature too low</td></tr><tr><td valign="top">Unit On-line<br><strong>531 - Module Added</strong></td><td valign="top">HBUS device detected</td></tr><tr><td valign="top">Unit Stopped Responding<br><strong>143 - Expansion module failure</strong></td><td valign="top">Plug-in not responding<br>Unit Not Responding</td></tr><tr><td valign="top">Walk Test Mode<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Sensor Group in Walk Test Mode</td></tr><tr><td valign="top">Walk Test Mode Attack<br><strong>393 - Maintenance Alert</strong></td><td valign="top">Attack Detected</td></tr><tr><td valign="top">Wrong PIN<br><strong>421 - Access denied</strong></td><td valign="top">Terminal: Bad PIN<br>Wrong PIN Entered</td></tr><tr><td valign="top">Zone Count Maximum<br><strong>140 - General Alarm</strong></td><td valign="top">Zone Count Maximum</td></tr><tr><td valign="top">Zone Count Mid-range<br><strong>140 - General Alarm</strong></td><td valign="top">Zone Count Mid-range</td></tr><tr><td valign="top">Zone Count Minimum<br><strong>140 - General Alarm</strong></td><td valign="top">Zone Count Minimum</td></tr></tbody></table>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.security.gallagher.com/knowledge-hub/configuration-client/appendices/xyz-event-mappings.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
